M500 Adhesive Mortar for common Tiles Laying

>>Shop Now<<

Raw Materials

• TPI Portland Cement Type I according to ASTM C-150  and TIS 15 part 1-2555 Standards.
• Limestone is thoroughly dried and  classified.
• High quality chemical additives providing with enhancing water

Absorption, adhesion strength properties thus eliminate the peeling off  tiles  and during tiles adjustment.

Instruction of preparation and application

1. Clean the substrate surface and moisten with water on the surface before laying tiles and let semi –dry.
2. Mix 1 bag (20 kg) of TPI M500 with 4.8 liters of clean water. Mix well until the mixture is homogeneous and apply immediately.
3. Apply the mixture of adhesive mortar on the substrate surface with 5 mm. thickness then set the notched trowel at 45 degree angle to the surface and drag it to create ridges and grooves.
4. Lay tiles onto the substrate then press or use the rubber hammer to tap each tile firmly.
5. Align the tiles and clean up in case of drop mortar or adhesive on the tiles or any other surfaces.

Remark

• Store in a dry place and avoid dampness.
• After mixing with water, product should be applied within 2 hours.
• Seal the bag tightly after used.
• Suitable for small common tiles and maximum width should not exceed 40 cm x 40 cm.

Suitable for floor and wall tilling for both indoor application and provides highly adhesive strength allowing the adequate time for tile adjustment. Save money and time.

Suitable to apply on floor or wall laying tiles both indoor and outdoor.

High Bond Adhesive Mortar for laying New tiles over the old tiles

>>Shop Now<<

Product characteristics

TPI M501 is high bond adhesive mortar for floor and wall applications for both outdoor and indoor. It can be applied for large tile, fiber board, wood flooring and parquet. It performs extremely high bond adhesive strength on concrete surface and allows to laying new tiles on the old tiles. During tiles paving, it gives adequate time for tile adjustment. Therefore, M501 is to use and save time and money.

Instruction of preparation and application

1. Clean the substrate surface to be tiling and to ensure that is clean and free from dust, grease, chemical and other contaminates to disturb the adhesive strength of mortar. In case of lay the new tile over old tile, to check and make sure that the old tile is strong enough and if there are not in good condition, it must be repaired with right approach before laying new tiles.
2. Mix 1 bag (20 kg ) TPI M501 with 4 liters of clean water until the mixture is homogenous.
3. Apply the mixture of adhesive mortar on the substrate surface with 5 mm. thickness then set the notched trowel at 45 degree angle to the surface and drag it to create ridges and grooves.
4. Lay tiles onto the substrate then press or use the rubber hammer to tap each tile firmly.
5. Align the tiles and clean excess adhesive from tiles and joints before it sets.

Remark

• After mixing with water, product should be applied within 2 hours 30 minutes.
• Keep in dry place and seal the bag tightly.

Suitable for Laying New Tiles over The Original Tiles Without extracting off.

TPI Extra High Bond adhesive cement for very large tiles (Marble tiles and Granite tiles)

>>Shop Now<<

Instruction of preparation and application

• Clean the substrate surface to until free from all dirt, Oil , chemicals, color stain, dust and any other contaminates which can effect to the bonding adhesive strength of mortar. Before tiling, make sure existing condition of substrate surface is suitable. Otherwise, the wall must firstly be repaired.
• Mix 1 bag (5 kg) TPI M503 (Extra High Bond Adhesive Mortar) with 0.9 – 1 liter of clean water until the mixture is homogenous. Apply the mixture a 5 mm. thick layer on the required surface. Then use a notched trowel at 45 degree angle to comb the mixture from the surface and drag it to create ridges and grooves.
• Lay tiles onto the substrate then press or use the rubber hammer to tap each tile firmly.
• Align the tiles as required and clean excess adhesive from tiles and joints before it sets.

Suitable for laying large tiles, Marble and Granite tiles with extra High Adhesive Strength and long lasting life.

Multi – Purpose Repair Mortar

Product characteristics

TPI M600 is suitable for repairing the small areas such as cracking area, wall scaling, breaking/ drilling marks, leakages, ceramic tile repairing etc.

>>Shop Now<<

Raw Materials

• TPI Portland cement type l according to ASTM c-150 and TIS 15 part 1-2555
• Fine limestone thoroughly dried and classified
• High quality chemical additives for enhancing extra high adhesive strength.

Workability, and for reducing cracking and shrinkage.

Remark: After mixed with should apply within 1 hour.  ( 1 bag (2 kg) per 0.35 – 0.40 liters of water) After opening the bag, should be use all the contents. If mortar are remains in bag, please seal tightly and keep in the dry place and not damp.

Suitable For Crack Or Split Up Repairing Or Plug The Break Or Drill.

Water Plug Cement

TPI M680 is mixed hydraulic cement with very fast in setting time and it can be applied both under Water and in the air. It sets within 3-5 minutes and suitable for holes or cracks in concrete or masonry  walls, swimming pool, leakage pipe and it can set  even under running water and able to stop active water leakage. It can be also used for the quick repair to walkway and anchoring bolts on concrete surface.

>>Shop Now<<

Preparation Procedure

1. Surface must be clean and structurally sound and remove all dirt and loos material. Chip the crack to at least 1 cm. depth  then cleaning and saturate the surface with water before plugging with mortar.
2. Mix TPI M800 with clean water at the ratio 4:1
3. Rapidly mix all together well and it should it should be used within 3 minutes.

Avoid reuse the hardened cement mixture.

Remark: When mixing 1 kg of water plug (TPI M800) with the ratio water volume amount is 500 cm²

 Application

• In case of repairing active water leakage, place the TPI M680  Mixture in your   hand until cement begin to setting then apply it in the  leaking region and keep pressing for 3-4 minutes and clear the excess material around the surface.
• In case of repairing the crack concrete, place TPI M680 onto the crack with trowel then clear excess materials around the surface. Cure it by spraying with water or covering a damp cloth for 3 hours.
• In case of plugging the anchor bolt holes in concrete, holes’ width must be at least 1 cm. then fill and press cement firmly with trowel and clear excess materials before cement sets.

Suitable for Repairing the leak, Stop water leaking immediately and special  Fast setting

High flexibility and no shrinkage. Or for repairing materials with cracks, leaks, longer service life than other types of grout materials. It can be adhered to many materials such as fiber cement, artificial stone, aluminum, metal, tile, gypsum board, ceramic and UPVC etc. can be used both indoor and outdoor. Through secure use. Can be painted over not slip.

>>Shop Now<<

FEATURED

• Highly elastic grout fillings 
• Fast drying, high adhesion, no shrinkage
• Fungus protection with special additives
• Internal and external use

HOW TO USE

1. Clean the surface dry, free of dust, oil, debris, seagrass and coating materials.
2. In case of adhesive. To glue a bar or placemats.
3. In case of a grout adhesive. Should be wide The depth of not less than 10 mm should be used adhesive paper to seal the two joints before firing. At least 1 hour passed. Then remove the adhesive.
4. When filling grout full. Must be smooth within 10-30 minutes.
5. Wipe up the excess with sponge. Or a cloth moistened with water 48-72 hours before use.

WARNING

1. Keep out of reach of children.
2. Keep in the shade and normal temperature.

TECHNICAL INFORMATION

Water consumption 300 ml / TPI Sealant (M611) 0.4 kg

For adhesive material.

Diameter x Thickness /Area 3 x 4 mm/ One glue to 1 pin will get 100 pins.
Diameter x Thickness /Area 5 x 10 mm depth/ One glue shot is a 12 meter tube.